Contents:

Introduction to the Edge‐20ST and HD

Safety Notice

Transport of Machine

Operating Instructions

Troubleshooting Guide

Warranty Information

Parts Breakdown

INTRODUCTION TO THE EDGE 20-ST & HD

Thank you for making the decision to purchase an Edge 20. This machine is proudly built in the USA, with quality materials and will give you many years of satisfactory service if properly maintained and used according to the guidelines in this owner’s manual.

SAFETY

DANGER: Indicates an imminently hazardous situation which, if not avoided, may result in death or serious injury.

WARNING: Indicates a potentially hazardous situation, which, if not avoided, may result in death or serious injury.

CAUTION: Indicates that machine or property damage could result if instructions are not followed.

NOTE: Provides helpful information.

Severe bodily injury or death can occur to you or other personnel if warnings found on this machine or in this Owner’s Manual are ignored. Read and Observe all statement and instructions found on the machine and in the Owner’s Manual.

DANGER:

Never leave the machine unattended while power cord is connected.

Always wear safety goggles and dust mask when operating this machine.

Never inhale dust created by the use of this machine

Any modifications to this machine may result in damage to the machine or injury to the operator or others nearby. Alterations to the machine will also void any and all warranty and liabilities.

Do not operate this machine around fuels, solvents, flammable floor finishes, thinners, wood dust or any flammable materials. Cigarette lighters, pilot lights, electrical sparks and all other sources of ignition should be extinguished or avoided. Work areas should be well ventilated.

Keep the power cord clear of the pad and in good condition. Always life the cord over the machine. Do not pull on the power cord in an attempt to move the machine or remove the plug from the wall. This could result in electrocution.

Do not use machine if it has been sprayed with water or left out in the rain. This could result in a shock injury or death.

Keep feet, hands, and loose clothing away from any moving parts on the machine to avoid injury. Disconnect power cord before changing the pad or when servicing.

CAUTION:

Damage can occur to the machine or to other property if instructions in the Owner’s Manual are not followed.

WARNING:

Do not operate this machine while under the influence of alcohol or other drugs.

Never allow individuals under age 18 to operate this machine.

Unplug machine from power source before adjusting height of handle or changing pad.

Never attempt to move p the machine by pulling the power cord.

TRANSPORT OF MACHINE

To transport this machine, the following procedure is advised:

Unplug machine from power source

Always leave a pad on the machine to protect the grip face from damage in transport and storage.

Wrap cord using built in cord wrap and handle as picture illustrates.

Raise handle and lock in upright position.

Tilt machine onto wheels and transport slowly.

When lifting machine, it is suggested for two users to participate. With one user on each side of the machine, grip lifting bars at the base of machine with one hand. Grip the handle

with the other hand and lift.

Secure machine when transporting in a vehicle to prevent movement.

Caution: The ST model weighs 130 lbs and the HD model weighs 165 lbs. Get assistance when lifting. Do not attempt to lift alone.

OPERATING INSTRUCTIONS

1. Move machine to work location. Never transport or store the machine without a pad to protect the grip face.

2. Check the pad. If it has become reduced to a thickness of less than ½” replace the pad.

3. To install or replace pad, follow these instructions:

a) Make certain power source is disconnected

b) Lock handle in upright position

c) Tilt machine back until the handle rests on the floor

d) Remove existing pad and replace with new pad. Center pad when placing on grip face

e) Press pad firmly into grip face

f) Return machine to upright position

NOTE: When using a EQP (PREP) “abrasive” pad, place the pad on the floor and slowly lower machine onto pad, making certain the pad is centered on the machine and RED pad. Do not operate PREP Pad or Sanding material directly on the grip face.

4. Connect cord to power source.

5. Release and lower handle to a comfortable position. Lock handle into position. The best operating position is at arm’s length to help with control of machine and to improve operator comfort. Maintain the machine flat on the floor for ease of operation. Raising or lowering the handle can cause the machine to pull to the right or left, and uneven pressure/wear on the pad surface. A neutral handle position will provide a neutral operation and uniform contact of the pad to the floor surface.

6. Squeeze the power bar with both hands to start machine. Release power bar to stop machine.

NOTE: Releasing power bar will immediately stop the machine

TROUBLESHOOTING GUIDE

NOTE: The rubber isolators on the EDGE-20 are considered a Wear Item. It is recommended to replace the entire set of all four isolators at least every 100 hours of machine operation to prevent failure and damage to the machine.

WARRANTY INFORMATION

This product is warranted to be free from defects in materials and workmanship under normal use and service for a period of two years from the date of purchase, when operated and maintained in accordance with our Maintenance and Operating Instructions. Damage due to misuse or improper care will not be repaired under warranty.

This warranty is extended only to the original purchaser for use of the product. It does not cover normal wear and tear parts such as electrical cable, rubber parts, pad driver, and motor brushes. NOTE: The rubber isolators are considered wearable parts. It is recommended that the entire set of four isolators be replaced every 100 hours of machine operation at a minimum.

If a difficulty develops with the product, contact your Authorized distributor or call us directly at the number below. Repairs and warranty consideration can only be conducted by approved distributors. Travel to and from the repair center is NOT covered by the warranty, and is the responsibility of the customer.

RPS’s liability under this warranty is limited to repair of the product and/or replacement of parts only, and is given to the purchaser in lieu of all other remedies, including INCIDENTAL AND CONSEQUENTIAL DAMAGES.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE SPECIFIED HEREIN. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE FACE HEROF. NO

WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY, SHALL BE IMPLIED. Please register your machine on our website within thirty days of purchase.

PARTS BREAKDOWN

Detail A

A:

•      1725 RPM 60Hz USE PART #300-01012Z

•      1725 RPM 50Hz USE PART #300-01052Z

•      3450 RPM 60Hz USE PART #300-01053Z

•      3450 RPM 50Hz USE PART #300-01054Z

B:

•      (2) 11 LBS WEIGHT USE ON HD MACHINES ONLY

C:

•      (2) 6 LBS WEIGHTS USED ON STANDARD MACHINES

•      (4) 6 LBS WEIGHTS USED ON HD MACHINES

EDGE 20 INCH FLOOR PADS: